REDHEAD® HYDROMASSAGE BATHTUB WATER TEMPERATURE MAINTENANCE HEATER OWNER’S MANUAL

OPERATING INSTRUCTIONS

WARNING

Prolonged immersions in hotter water may induce hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98.6°F. The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness, lethargy, drowsiness and fainting.

                                                                  SAVE THESE INSTRUCTIONS

Your Redhead Hydromassage Bathtub Water Temperature Maintenance Heater has been designed and engineered to allow the bather to select his or her desired bathing temperature by adjusting the water temperature of the water while filling the bathtub, and then the maintenance heater automatically takes over to maintain the temperature selected. The Redhead heater utilizes Patent Pending SmartSense Technology to automatically sense the bath water temperature that you have selected, and without any additional intervention on  your part, maintains that pre-selected bath water temperature for the normal bathing duration.

 

Once properly installed, there is no required preventive maintenance or adjustment necessary to keep your Redhead heater operating for years. Unlike heaters of lesser technology typically found on low end hydromassage bathtubs, the Redhead heater is designed to ensure that there will never be a need to reset a tripped over-limit device, even if the bathtub is filled with high temperature bath water initially. Nuisance tripping is a thing of the past with the Redhead heater.

 

So, now is the time to sit back, relax in your hydromassage bathtub, and let the state-of-the-art Redhead heater effortlessly help you soak away your tensions. Thank you for your decision to have your hydromassage bathtub heated with the Redhead heater. We appreciate your confidence in selecting our product.

 

The following sections of this manual will help you should your Redhead heater ever fail to function as designed, or should you need to contact us for any reason.

TROUBLESHOOTING

Symptom 1

Heater will not maintain the desired water temperature I wish to maintain.

Action

a.   Check to make sure there is electrical power to the heater. An ON light is located on the top of the heater electrical enclosure and is ON whenever the heater is heating.

b.   If no ON light is seen, test electrical outlet that heater is plugged into for power.

c.   If no power at electrical outlet, restore power to outlet

d.   If heater ON light won't come on, check:

1.       Blocked suction fitting (remove blockage from suction fitting)

2.       Blocked jet(s) (remove blockage from jet(s)

3.       Adjustable jets turned OFF (open all jets)

4.       Water below top of jets (add more water to tub)

5.       Pump not running (turn ON jet pump)

6.       Pump is cavitating (check suction piping for leaks and turn pump OFF/ON)

Symptom 2

Heater light is ON, but I can’t feel hot water coming out of the jets.

Action

a.    You will not feel hot water coming out of the jets, as the heater is designed to simply maintain the water temperature, not heat up a cold bath.  Add more hot water, and the heater will maintain the warmer temperature you have selected.

Symptom 3

Heater trips the Ground Fault Circuit Interrupter (GFCI) whenever it comes ON.

Action

a.   Unplug heater from power source receptacle and test GFCI by pushing TEST button on GFCI if GFCI does not trip or reset, replace GFCI.

b.    If GFCI tests OK, immediately unplug heater from power source

c.    Return the heater to Dealer that supplied it, for service, OR

d.    Leave heater installed in plumbing, unplugged from the power source and contact Aquatemp Service Department by calling, faxing, or online as indicated below.  A replacement heater can be delivered to you in one day after your call is received, anywhere in the USA.

Symptom 4

I can’t find any controls on my heater

Action

a.    Your heater has no user controls.  All functions are automatic and no adjustment is necessary to maintain the desired bath water temperature.  No user serviceable components are located inside your heater’s electrical enclosure and removing the electrical enclosure from the heater body will void your Limited Warranty.

___________________________________________

 

SPECIFICATIONS

Bath Water Temperature Maintenance Heater

Electrical Rating: 120 Volt AC/ 5.3 amps

Output: 2156 BTU

Safety Conditions Protected:

a.    Low water

b.    Blocked suction

c.    Blocked return

d.    Closed jets

e.    Pump cavitation

____________________________________________

 

 

___________________________________________

 

LIMITED WARRANTY

Your Redhead heater is covered by a one (1) year Limited Warranty which is packed with your heater.  Consult the printed Limited Warranty for all terms and conditions contained therein.   Should your Redhead heater fail to operate as designed for any reason, simply contact the Redheadheater.com Service Department (see above) for prompt service.  NOTE: Consult your Installation Instructions for information pertaining to Risk of Fire, Electrical Shock or Injury to Persons.

Contac us: Phone: 909-520-1769
  
 

                                               Back to Customer Care